Posts Tagged ‘Narberth’

Media Air Conditioning Tip: Things to Check on Your Broken AC Before Calling a Professional

Tuesday, May 29th, 2012

A broken air conditioner is a stressful situation, especially since you’re considering whether you need a Media AC professional to come out. No one likes spending hundreds of dollars to have a professional take a look at their system, so before you call anyone, make sure to check these problems. You may be able to fix the problem on your own without spending a dime.

 Thermostat

The thermostat is one of the most common problems you’ll have with an air conditioner.  Make sure the thermostat wasn’t knocked out of position and the sensors near your coils are in the right place. Often times, a bumped sensor or a slightly off thermostat can cause this kind of problem and as a result, you’ll be left without steady cooling.

 Check Your Filters

Another common problem that can cause issues with your air conditioner is filter clogging. While the system will continue to run with a clogged filter, there are a few issues that might pop up – it could smell funny or you might notice icing on the outside line (a major problem). If you allow the filter to get so clogged as to block the air flow from your system, you can expect a number of problems to crop up.

 Blower Belts

Check the system’s blower belt for damage like cracking, excess slack or general wear. A blower belt that isn’t properly installed or that needs to be replaced will reduce air flow which can result in ice buildup or poor air flow – it will make it harder for your system to maintain a steady temperature.

 Check the Outdoor Unit

Check to make sure nothing is blocking the outdoor unit. Clean the condenser coils and remove any debris that might have built up around the outdoor unit. Often, slowed air flow is caused by nothing more than leaves piled in front of your condenser.

If none of these problems is the culprit or if you fix them all and your system continues to struggle, it is time to call a Media air conditioning professional like Cool It Heating & Air Conditioning.

Tags: , , , , ,
Posted in Services | Comments Off

Narberth Heating Replacement: 5 Reasons to Replace Your Furnace

Wednesday, February 1st, 2012

Many Narberth homes are heated with furnaces, since they generally provide safe and efficient heat.  Furnaces have also improved dramatically over the years as manufacturers find ways to make them more efficient. Even if your furnace has been reliable for many years, it may be worth the money to replace your old furnace with a newer, more efficient model.

Here are five major benefits to upgrading your furnace.

1. Lowering Your Utility Bills

Whether you realize it or not, your current furnace could be costing you more than it should in heating bills. If your furnace is 15-20 years old, it’s probably not heating your home as efficiently as the newer models with higher AFUE ratings. Even if your heating system has been replaced within the last ten years, the technology has advanced enough to consider an upgrade.

2. Fewer Repairs

Repair costs can add up if you are constantly repairing your furnace. Routine maintenance for your furnace can help reduce the need for repairs, but as furnaces age, they tend to need more repairs and replacement parts. If you need frequent repairs for your furnace, it may be time to replace it with a newer one.

3. More Consistent Heat

While maintaining consistent temperatures throughout your home involves several factors, such as insulation and thermostat control, your furnace could also be the reason you aren’t getting enough heat to all parts of the house. If some rooms are colder than others, or if your heating bills have recently gone up, it may be time for a furnace replacement.

4. Reduce the Chances of a Breakdown

When a furnace breaks down, it not only leaves you without heat, but it is also a major expense. Budgeting for a new furnace before it breaks down will put less financial burden on you than needing an emergency furnace replacement. Newer model furnaces are also more reliable and less likely to give you problems if maintained properly.

5. Safety

There’s higher potential for safety concerns with older or poorly maintained furnaces. In addition to fire hazards, carbon monoxide poisoning is another serious threat. When the heat exchanger stops working because it’s corroded or faulty, carbon monoxide can leak into the home. If you’ve had your furnace for more than 20 years, it could create safety hazards that you may be unaware of.

No matter how long you’ve had the furnace in your Narberth home, it’s always wise to speak with a qualified HVAC technician about furnace upgrades, particularly if you have expensive heating costs. Call Cool It Heating & Air Conditioning today to talk with one of our heating experts about furnace upgrades.

Tags: , , , , , ,
Posted in Services | Comments Off

Narberth HVAC Question: How Much Ventilation Do I Need for My House?

Friday, January 27th, 2012

By now you’ve probably heard how important it is to have good ventilation in your Narberth home. Especially if your home was built in the 1980s or early 1990s when ventilation issues were prevalent, you may not have enough clean air moving through your home. But, how much ventilation do you need? What is enough and if you don’t have it, how do you ensure your home is retrofitted properly?

How Much Ventilation?

Most recommendations for ventilation come from the Home Ventilation Institute, which provides a series of standards of measurement for builders and contractors retrofitting homes for better ventilation. Here are some of their recommendations and how they might apply for your home:

  • Bathroom – Small bathrooms (less than 100 sq. ft) need 1 CFM per square foot of bathroom. The number goes up for each fixture if you have a large bathroom.
  • Kitchens – Your kitchen range needs at least 100 CFM if against the wall and upwards of 150 CFM if on an island.
  • Ventilators – If you have an HRV for your home, you should have at least 100 CFM for 2,000 square feet and another 50 for every 1,000 square feet of home size being ventilated.
  • Home Ventilators – The actual volume of CFM for ventilators depends on the type of ventilator being used. For example, a whole house ventilator needs upwards of 6,000 CFM for a 2,000 square foot home. Attic ventilators need 1,400 or more.

So, what does this mean for your home? It means in general that you need a lot of ventilation and that the best way to get it is through mechanical ventilation techniques combined with your air handler and ductwork.

Especially if you recently added insulation and weather proofing to your home but have not yet updated your ventilation, you might have a major air quality problem, so have a Narberth professional measure your home’s air flow as soon as possible.

Tags: , , , , ,
Posted in Services | Comments Off

How to Handle Your Finicky Narberth Heat Pump

Friday, December 16th, 2011

Your Narberth home’s heat pump is designed to keep you comfortable. Warm weather, cold weather – it doesn’t matter. It should turn on when you need it and turn off when you don’t. So, when the device starts turning on and off without reason or when you need it to stay on, what exactly is the problem and how can you fix that problem without losing the heating or cooling capacity of your device.

Common Causes of the Problem

There are a number of reasons why your heat pump would turn off shortly after turning on, and most of the time this occurs in heating mode. If it occurs in cooling mode, you should have the device inspected immediately because there is likely something wrong with a core component like the compressor. For heating mode issues, here are some common problems:

  • Dirty Coils – If the coils are dirty, the device won’t be able to properly operate, especially if it has been some time since the last cleaning. Both sets of coils need to be cleaned at least once a year to avoid this becoming a problem.
  • Low Refrigerant Charge – If the refrigerant gets low, you’ll need to have it recharged because the pressure in the device will drop and it will therefore turn off after a few minutes of use.
  • Defrost Timer – If the defrost timer is forcing the device into a defrost cycle too often (usually it is set to 30, 60, or 90 minutes), the fan might turn off every few minutes after turning on. This is a common problem and is usually due to a thermostat or switch issue which can be fixed relatively easily.

Another thing to ask yourself when this problem occurs is whether the device is heating properly when on. Defrost timer issues don’t usually impinge on the heating ability of the device, while low refrigerant can. You want to make sure the device is working properly when on and not just cycling on and off without heating capacity.

Based on what you find, you’ll need a technician to take a closer look and ensure everything is working properly. Most repairs for this type of problem are relatively simple.

Tags: , , , ,
Posted in Services | Comments Off

What’s the Difference Between a Furnace and a Boiler? A Question from Concordville

Monday, November 28th, 2011

When it comes time to choose a new heating system for your Concordville home, there is a good chance your choices are limited. Most homes already have either forced air or radiant heat equipment installed so choosing something different would be costly and unnecessary. But, if you have a choice or are moving into a new home, here are some things to consider regarding the difference between furnaces and boilers.

What a Furnace Does

A furnace uses a fuel like gas, oil or electricity to heat a series of coils in the device. The furnace then uses a blower to push air across the heated coil and into an air handler where it can be distributed throughout your home. This is called a forced air system and requires a combination of ducts and filters to keep air moving smoothly and cleanly throughout your home.

If you have access to gas, a gas furnace with an AFUE of 90% or higher is one of the most efficient and cost effective ways to heat your home.

What a Boiler Does

A boiler is different in that it uses water as the heat carrying medium, not air. Boilers still need gas, oil or electricity to heat up the water in the system, though they often use less of it than a traditional furnace – depending on the age of the furnace and the boiler. After water is heated in the boiler, your radiant heating system carries the water to baseboard heaters or radiators throughout your home. This form of heat is preferred by many because it doesn’t require ductwork (which requires extra maintenance) or extra air filtering and it is more humidity friendly in a large home.

In terms of efficiency, both boilers and furnaces are efficient if you’re buying a new model. Capacity is also evenly matched. Boilers take the edge in comfort level and if you have the budget, you can install radiant floor heating which allows you to pipe hot water directly into bathroom floors or your living space so that you never again need to walk on cold floors. Another benefit of radiant heating is that the system will hold heat much longer and then release it over time instead of turning on and off a lot as a furnace tends to do.

Tags: , , , , , ,
Posted in Services | Comments Off

Heating System Preventative Maintenance: Some Pointers from Narberth

Monday, November 7th, 2011

Ben Franklin once said, “An ounce of prevention is worth a pound of cure.” His famous quotation can apply to many things in life, including the heating system in your Narberth home. While heating systems in Ben Franklin’s time consisted of wood burning stove and fireplaces requiring little maintenance, today’s sophisticated furnaces and building controls require a good dose of preventative maintenance in order to avoid mechanical failures and inefficient operation.

For example, a furnace runs better and lasts longer when you maintain a regular schedule of filter cleaning or replacing. A dirty or clogged filter can restrict airflow from the furnace into your home’s ventilation system and cause the furnace to work harder, putting more wear and tear on it and taking months, if not years, off of its useful life. If your furnace uses disposable filters, check them every month and replace them if necessary. If your furnace uses an electronic filter that requires cleaning, check it on a monthly or semi-monthly basis and clean it with soapy water and a hose. Be aware of the change of seasons which could add extra pollutants into the air like pollens, ragweed, and cottonwood. This debris easily finds its way into the filters and creates an unhealthy indoor environment.

You can also perform a simple visual inspection of working components inside your furnace by removing the access cover and checking – with a flashlight – for loose fan belts, frayed electrical wires, or a build-up of dirt and dust. Simple solutions include tightening or replacing belts, repairing wiring, and vacuuming out dirt and dust with a hose attachment. All of these actions will keep your furnace working better and prevent future failures.

You can also do a visual check of your home’s ventilation system, paying close attention to any cracks in duct seams or holes in flex ductwork. Using sealing cement or duct tape can usually fix these problems and allow for better, unrestricted air flow. Again, these actions will help your furnace work more efficiently and avoid premature failures.

Maybe the best advice for preventing heating system breakdowns is to have a regular maintenance schedule with a local qualified heating contractor. Most contractors can set you up with annual furnace and ventilation system inspections. Having a service agreement – as a rule – gives you priority emergency repairs and discounts on parts and services. Besides that, planned maintenance is also preventative maintenance, something that will give you peace of mind in the long run.

Tags: , , , , , ,
Posted in Services | Comments Off

How Effective is Geothermal Heating? A Question From Concordville

Wednesday, October 5th, 2011

Geothermal heating is an efficient way to use the Earth’s natural resources to heat a building’s interior, including your Concordville home. But is it an effective way? The simple answer is yes.

Consider the cost of geothermal heating. Once you get past the initial installation costs of a geothermal heating system, which are higher than other conventional heating systems, its operating costs are much lower because of its use of a natural, renewable heat source – the Earth. If you plan to stay in your home for many years, a geothermal heating system will likely pay for itself because according to International Ground Source Heat Pump Association, geothermal operating efficiencies are 50-70% higher than other heating systems, which represents a substantial lowering of energy costs.

And according to a leading electric utility company, the cost of electricity for operating a geothermal heat pump is lower than any other heating system which includes natural gas, propane, and oil.

Beyond lower energy costs, geothermal heating leaves a smaller carbon footprint than other heating systems. According to the U.S. Environmental Protection Agency, carbon dioxide (CO2) emissions from the average U.S. home is 17%, most of which comes from burning fossil fuels for electricity. Geothermal uses natural heat from the ground and therefore uses 30-60% less energy than more conventional heating and cooling systems. Using less energy equals less carbon dioxide production.

A geothermal heating system is only as effective as the equipment used to deliver it throughout the building. The most common delivery method is through a ground source heat pump. This pump pulls the heat from the earth and distributes it. When properly installed and maintained, a ground source heat pump can last 15-20 years and provide an excellent source for heating – and cooling.

The components of a geothermal system also include a compressor, air handling unit, and duct system. When all are installed and maintained correctly, a geothermal heating system will be just as effective in heating a building’s interior as any other heating system. Just be sure you hire a qualified heating and cooling professional to install and service your geothermal heating system.

Tags: , , , , , ,
Posted in Services | Comments Off

How Do I Reduce Dust in My Home? A Question From Narberth

Wednesday, August 24th, 2011

Dust is everywhere in Narberth. There is no way to stop it from occurring, so instead we turn to cleaning and filtration to keep the amount of dust circulating through the air to a minimum. Luckily, there are quite a few things you can do, even without installing new equipment, to reduce your dust levels.

Duct Cleaning

First on the list is regular duct cleaning. You dust your furniture and your floors, so why not clean out your ductwork? Properly cleaned ductwork is very important because of just how much stuff can build up in there over time. Imagine regular air flow in an enclosed space that never gets cleaned. How much dust and debris do you think could build up over the course of a year? Hint: it’s enough to keep a steady flow of dust in your indoor air.

Professional duct cleaning is important and should be done once every year or two depending on how often you use your home comfort system. However, you should also clean in and around the vents and ducts in your home where you can reach. This can be done weekly and will help immensely to reduce dust.

Filtration

Most air filters equipped with high quality HEPA filters work extremely well to remove dust from the air. Because HEPA filters can capture particles as small as 0.3 microns, they won’t just remove dust, but pollen, pet dander and even mold. Mold especially is a problem that occurs in far greater frequency in homes without filtration.

Simple air filtration is an affordable solution to a lot of different contaminants, so it’s a good fit for any home. However, there are more powerful systems as well that will reduce both dust and pathogens like bacteria – these purifiers use ionization to draw particles from the air electronically.

Humidity

Humidity imbalance can cause dust problems as well. Low humidity leads to more dead skin and dust in the house, while high humidity causes the development of dust mites. Properly regulating your humidity to slightly less than 50% will create a perfect environment in which less dust is created and circulated in your home.

The best way to reduce dust is to take a three pronged approach to indoor air quality. Cleanliness is always first on the list, but after that don’t neglect the value of filtration and proper humidity control. When used properly, these three things will ensure dust never bothers you again.

Tags: , , , , ,
Posted in Services | Comments Off

What to Look for when a Home is 10 Years Old

Monday, July 4th, 2011

A ten year old home is likely to be in great condition, presuming the previous owner(s) treated it well. But, there are some things you should watch out for that can arise in newer constructions, even if they were treated well.

Poor Craftsmanship

While it is possible for a 100 year old home to have poorly crafted parts, it’s highly unlikely if the house is still intact and is being sold this long after it was built. Newer homes, however, wouldn’t show signs of cheap materials or shoddy work until a bit later in their life. That’s why it is important to pay for a thorough inspection of the property as soon as possible – definitely before it is purchased and possibly again afterwards to check for possible improvements.

Specific things you should check for include roofing, your heating and cooling systems, the insulation and the drywall used. Especially in freshly renovated or built houses it’s impossible to be sure a home was built with the highest standards of modern craftsmanship.

Proper Maintenance

For a home that is only 10 years old, there is a good chance you can get the original records for the heating and cooling system, any appliances in the home and all maintenance performed on them since their installation. If not, don’t fret – a good technician will be able to easily check the status of a piece during an inspection.

You should also check to find out the last time the sewer lines and plumbing were inspected. Owners of new homes often forget to have these things checked because they never deal directly with the contractors after the home is bought. To avoid falling into that trap, you should make sure the maintenance plans have been followed carefully and kept up with since the system was installed.

Overall, if your new home is only 10 years old, you are likely in a very good place. The home will be in good condition, the parts will be new, and your heating and cooling system should be efficient. Original parts installed during construction may need to be replaced, but otherwise, if everything else checks out, you can count on having a comfortable, wonderful place to live for some years to come.

Tags: , , , ,
Posted in Services | Comments Off