Posts Tagged ‘Lenni’

Concordville Heating Tip: Sources of Carbon Monoxide

Monday, December 26th, 2011

The risks of carbon monoxide have been well documented for years. It can be fatal at high concentrations, but even in low levels in your Concordville home  it can be poisonous enough to make you sick.

What you may not know is that there are many sources of carbon monoxide, also known as CO. This poisonous gas is formed by any incomplete combustion process. Since combustion is not 100% efficient, that means carbon monoxide is released any time something burns.

To be more specific, here are some examples of carbon monoxide sources you might encounter around your house:

  • A furnace or chimney can leak exhaust gases, including CO, into the home if it has been improperly sealed or vented. For example, if the chimney has a small crack in the flue that goes unnoticed, CO from the fireplace can be vented back into the house.
  • A furnace supplied by an under-sized gas line will often burn the gas at a sub-optimum temperature. The result is incomplete combustion of the gas, which means a source of CO.
  • Old, dilapidated or poorly maintained heating systems are a big culprit. Often the seals or fittings are loose on these units, causing CO to leak out of them and into your house. Or they may not burn fuel as efficiently as they used to, so carbon monoxide is more readily released.
  • Using machinery, like a propane generator or a gas-powered saw, in a poorly vented garage can be very dangerous. Sometimes people don’t think about this one because the garage is large enough that it seems to be ventilated better than it is.
  • There’s a reason that barbeque grills are labeled for outdoor use only: they release a lot of carbon monoxide. Both charcoal and propane grills should only be used outdoors, and you should avoid the smoke from charcoal in particular as much as possible.
  • Smoking tobacco releases carbon monoxide into the air, along with other potentially dangerous gases.

There are plenty of other sources, as well, but those are some common ones. To protect yourself and your family, make sure any areas where combustion occurs are well-ventilated, keep your HVAC equipment well-maintained and in good repair and invest in a home CO detector. They are inexpensive, and many are combined with a smoke detector, so you only need to buy one unit.

Springfield HVAC Tip: What to Do About an Ice and Snow Covered Heat Pump

Wednesday, December 14th, 2011

It’s very common for heat pumps to ice over in the winter time in Springfield. It can be due to freezing temperatures and icing outside or it could be due to constant running of the heat pump or excess moisture on the coils. However, while a bit of ice on the heat pump is relatively normal, the entire unit should never be covered in ice – such a thing is not only hard on the machinery; it can result in no heat for your home.

How to Handle Ice and Snow on the Heat Pump

Should your heat pump become covered in ice or snow in the winter time, there are a few things you can do and some things you should not do. First, check to make sure the problem isn’t related to a broken defrost cycle timer. The heat pump should go into a defrost cycle every 30-90 minutes to keep excess ice from building up. If this doesn’t happen, it should be inspected for a thermostat or sensor problem.

To actually remove the ice from the unit, never use a sharp object to pick the ice clear. You can easily damage the coils or another part of the unit and leave it permanently broken. The best way to remove ice from your heat pump is to rinse it off with a hose – even cold water will remove ice. Just be sure the defrost cycle is ready to come back on so the water used to rinse away the ice doesn’t freeze.

Remember to check your emergency heating source and make sure it is switched on while this is happening. Your heat pump likely won’t work properly while iced over and if it is left in the on position, excess stress on the device will cause damage.

To avoid this kind of damage, turn off the heat pump and turn on your emergency heating source, then clear away the ice and check the defrost timer. If everything works properly, turn the heat pump back on, but if you find any problems, call a heating contractor to do a more thorough inspection of the device before you use it again.

How Often Should I Have My Geothermal System Checked? Some Pointers from Newtown Square

Wednesday, November 23rd, 2011

The beauty of having a geothermal system in your Newtown Square home is that is requires very little maintenance. They have fewer mechanical components are than other heating systems – and most of these components are underground or inside, shielded from the outdoor elements. The underground tubing usually is guaranteed to last 25-50 years and inside components are easily accessible for servicing.

Nonetheless, keeping a geothermal system working at peak efficiency is very important. If the geothermal system loses some of its efficiency, it will cost home and building owners money in energy costs, which makes little sense since geothermal system installation costs are higher than most other heating systems.

Its key component is the ground loop system, polyethelene tubing which carries refrigerant from below the Earth’s surface and back to an above-ground compressor. When installed correctly, the buried ground loop can last for decades. A leak in the metal tubing is usually the only problem if the ground loop is not installed correctly. In the case of a leak, it may be necessary to dig up the tubing – often installed at least ten feet below the surface – and repair the leak.

Other geothermal system components include its air handling unit, compressor, and pump. These components require periodic system checks by qualified professional heating and cooling technicians. Maintenance normally requires filter changes and component lubrication, to name the most common. In some cases, building owners can perform their own filter replacement and refill of lubricants. However, it is recommended that an experienced technician perform a multiple-point inspection of the geothermal system components, usually during regularly scheduled service calls.

Heat Pump Filter Care: Some Advice from Ridley Park

Wednesday, October 19th, 2011

On the whole, heat pumps are a efficient, durable and effective way to heat your Ridley Park home. They are built to run all year round without needing any more maintenance than your average furnace or air conditioning system and they have an average lifespan comparable to those other types of home comfort systems as well.

That’s not to say that there aren’t things you can do to keep your heat pump in good working order, however. Keeping up with the professional maintenance visits is an important step to take along these lines to be sure, but there are also some other things you can do on your own as well to help ensure the continued efficiency and health of your heat pump system.

Proper filter care is an important part of keeping your heat pump working the way it should. If you don’t have a heat pump yet but are thinking of getting one, make sure you have the installation technician show you where the filter is located and how to replace it.

If your system’s already been in place for some time, you can still find out how to care for the filter from your annual maintenance technician or you can probably even find it on your own by taking a close look at your heat pump. The filters are meant to be removed on a regular basis so they’re typically not hard to get to. However, you should always be sure that all of the power to your heat pump is turned off before you open it up to try and find, replace or clean the filter.

Most heat pump filters are meant to be changed or cleaned about once every 90 days or so. However, the specific requirements for each system can vary considerably, so you should be sure to find out what is recommended for the model of heat pump that you have.

Also, you’ll want to know what type of filter you have so that you can purchase the appropriate replacement. The model number for each filter should be clearly printed on it, so simply slide your current filter out and make note of the number so that you can purchase the correct type as a replacement.

Most heat pumps have replaceable filters, but some still do have permanent filters that are meant to be cleaned and then returned to service. If you have one of these types of filters, be sure to read the instructions for cleaning carefully before proceding.

What Is the Single Biggest Money-Saver Upgrade You Can Make? A Question From Lenni

Monday, September 26th, 2011

While it would be great if there was a simple answer to this question, the real right answer depends to a great extent on your own particular situation in your Lenni home. There are literally dozens of steps you can take to save on your home heating and cooling costs, and which ones are most appropriate for you will have a lot to do with what you already have, how you use it and where you live.

For instance, if you have a well-insulated house but your HVAC system is more than 10 or 15 years old, investing in a new system will almost certainly save you a ton in the long run. Even if your existing system is working well, the newer systems available are simply so much more energy efficient that having one will cut your monthly bills dramatically.

Plus, you will be replacing your system relatively soon anyway if it is that old, so you might as well start saving now on your heating and cooling costs.

If you already have an energy efficient HVAC system, your thermostat might be the place to look when you want to try and cut your energy costs. A programmable or wireless thermostat might be just the ticket you need to cut back even more on your energy bills because of the added control it gives you to more precisely regulate the temperature inside your home.

Particularly if you have a large house, you might even consider having a zone control system put in so that you can set different temperatures for different areas of the house. After all, there is no need to be paying to regulate the temperature in a part of the house that is unoccupied.

Looking at Moving to a New House – What to Look for in a Furnace? A Question From Lenni

Friday, September 16th, 2011

What are the Minimum Efficiency and Maximum Age of a Furnace?

Most new homeowners in Lenni overlook simple things like the maintenance and age of their furnace. However, if you know exactly what your furnace should do and how long it should last, you’ll be better prepared to setup your maintenance visits and start looking for a new model. So, how do you tell what your furnace should provide? Here are some easy tips.

The AFUE Rating

Furnaces built in the last 20 years come with an AFUE rating that tells you how much of the fuel they consume is effectively converted into heat. If your home’s furnace has an AFUE of 80% that means it will effectively convert 80% of the fuel it consumes into heat. However, if your furnace has an AFUE of 98% it will convert 98% of the fuel it consumes into heat.

These ratings are designed to show you what to expect from your system from month to month. If the furnace suddenly starts using far more energy and produces the same amount of heat, you know that the AFUE is no longer accurate. It’s either a sign of a problem or that your furnace needs to be replaced.

Maximum Age

No manufacturer likes to give a maximum age for their furnaces because they can last for much longer than originally rated in many cases. However, most furnaces will come with at least a 10 year limited warranty for the heat exchanger and a 10 year limited warranty for the parts. So, if you take good care of your system, they expect it to last at least 10 years.

However, if you maintain your system annually, check the filters throughout the winter and don’t push it too hard when it gets cold out, your system could last even longer than the limited warranty, allowing you to enjoy an efficient furnace for years to come.

Moving In

While you’ll have your new home inspected, a working furnace doesn’t necessarily mean a good furnace. Make sure to learn just how old the furnace is, how much maintenance it needs, and the level of efficiency you can expect. It may be in your best interest to simply have it replaced now and start saving on your energy bill immediately instead of two or three years down the road as it continues to get worse.

What Can You Do Yourself if Your Central AC Unit Does Not Work? When Should You Call a Malvern Professional?

Monday, August 29th, 2011

If your air conditioning system suddenly stops working or is not keeping your Malvern house as cool as you think it should, the chances are good that you will have to call in a professional to make the necessary repairs and get you back on track. However, there are a few things you can do on your own before you make that call to ensure that this really is something you cannot take care of on your own.

While it may seem obvious, the first thing you should check is the thermostat to make sure that it is set to a temperature that will trigger the air conditioning to come on. If your thermostat for some reason is set too high, then the air conditioner will not receive the signal to start cooling the house. This is an easy fix, of course, and you will be back up and running in no time.

If the thermostat is indeed set where it should be, the next thing to check is the air filter. Most people with central air conditioning know that they should change the filter once every month or so, but this seldom actually happens.

If it has been a while since your air filter was changed, there is a good chance that it is clogged and therefore blocking air from circulating from the air conditioner through the rest of the house. This is an easy enough fix, as all you need to do is replace the current air filter and your system should be able to pick up right where it left of. However, if the blocked air filter has also caused ice to form behind it, you may have to wait for a couple of hours until the ice has a chance to thaw.

Next, you will want to check and make sure that the air conditioning system is actually getting power. Look to see if any of the breakers are tripped or if there may have been a current interruption for any other reason that is within your power to fix. If this is the case, though, it is a good idea to turn the air conditioning system off before you attempt to restore the power.

If none of these measures are able to get your air conditioning system up and running again, you should not hesitate to call a professional. Many air conditioning repairs are quite basic, but they still need to be performed by a licensed professional.

Federal Energy Efficiency Rebates Explained: A Guide From Broomall

Wednesday, August 17th, 2011

You’ve probably seen the advertisements and heard the sales pitches all over Broomall. Upgrade your furnace, air conditioner, water heater, or insulation and receive a federal rebate on your taxes for a percentage of the installation cost. The government is seriously invested in improving the energy efficiency of the country, cutting electric bills and helping people stay comfortable. Here’s a quick look at some of those rebates and how you can tap into them.

Energy Efficiency Credits

There is a standard tax credit of 10% of the cost up to $500 or a specific amount between $50 and $300 for any upgrade made to your existing home for heating, ventilation, air conditioning, insulation, roofs, or water heaters. These upgrades must be made on an existing home in which you currently live – rentals and new construction homes are not eligible.

Green Energy Credits

Even better credits are available if you plan on installing a geothermal heat pump, wind turbine or solar system – either PV panels or solar heating. The tax credit here is 30% of the cost with no upper limit. This applies to any existing or new homes and can be applied to both primary and secondary residences.

Are the Tax Credits Worth It?

The big question is whether these credits are worth the investment in a brand new system? For the most part, it depends on your particular situation. If you have a 30 year old furnace and are planning on an upgrade anyways, why not take advantage of a nice rebate and get a more energy efficient system to go with it? However, if you just replaced your furnace three years ago and it works very well with a high energy efficiency rating, it might not be worth the investment.

Learn More

The Energy Star program run by the EPA contains detailed breakdowns of the 2011 tax credits, including what systems are eligible and how to go about claiming them on next year’s taxes. Learn more by visiting their official page.

Mold…What if I Have Mold? A Question From Thornton

Friday, August 12th, 2011

No one wants to find mold. But, even if you’re not aware of it, mold is probably lurking somewhere in the damp, dark crevices of your Thornton home. And mold is particularly likely to grow in homes with improperly regulated humidity. Luckily, because we know that, there are quite a few things we can do to stop the growth of mold in its tracks and save your home from unsafe air quality and the damaging effects of those little spores.

The Dangers of Mold

As mold grows, it can do damage to your woodwork and other areas of your home. It also contributes to indoor air quality issues because mold spores are a significant indoor air contaminant. Many people are allergic to mold spores, so if you or someone else in your household has experienced allergy symptoms that you can’t explain, mold spores are a likely culprit.

If you find out there is mold in your home, don’t panic just yet. There are some things you can do to address the problem and get mold out of your house for good. Your main task will be getting rid of the mold that is already there. This isn’t necessarily easy because of the areas mold tends to grow in. But, even with the proper air quality treatment, your home and health is still at risk if you don’t target that existing mold fast.

Stopping Mold in Its Tracks

Just getting rid of existing mold won’t solve the problem, though. Mold keeps coming back as long as there is an environment to support it – and that means moisture. Mold requires water to grow, so the chances are that if you have a mold problem in your home, you also have a humidity problem. Getting your indoor humidity under control will make it much easier to remove and keep mold out of your home for good.

There are plenty of good humidification systems on the market today. They can be easily integrated into your home heating and cooling system and provide great, consistent humidity control. Make sure you get one that’s large enough for your home. An indoor air quality professional can help you make that determination. Once you have a good humidification system in place, you’ll notice a huge difference in your overall indoor air quality, and hopefully the problem won’t return anytime soon.

What Are the Benefits of Having a Ceiling Fan in Villanova?

Friday, August 5th, 2011

There are definitely some days in Villanova every year that would be pretty miserable to get through without the benefit of a central air conditioning system in your home. And since you have a central air conditioning system in place, it may seem silly and unnecessary to think about having ceiling fans put in as well. There are actually quite a few benefits of having ceiling fans, however, regardless of what kind of central air conditioning system you have or how powerful it is.

Ceiling fans are not too expensive to put in and they take very little energy to run. But the breeze they produce can have a powerful cooling effect on a room. In fact, running a ceiling fan can make you feel up to eight degrees cooler than you would otherwise.

While this certainly is not enough on a really hot day, it can actually be plenty when the weather is not all that hot. But even if you have your central air conditioning turned on, you can still benefit from running your ceiling fan. That is because the cooling effect of the ceiling fan can allow you to turn up the thermostat for your air conditioner, resulting in a considerable savings on your cooling bill.

Because ceiling fans are so cheap to run, they can complement central air conditioning systems nicely and will provide significant savings over time. Running an air conditioning system alone can certainly keep you cool and comfortable all summer long, but it will also cost you considerably more than if you were to throw a ceiling fan into the mix as well.

And that is not all a ceiling fan can do to help you stay comfortable all year long. In fact, ceiling fans can also be of use in the winter because they help to return the warmer air to the lower parts of your rooms. Warmer air will naturally rise, meaning that your heating system will have to work harder and harder to keep the air in the lower part of your room warm. But with a ceiling fan in place, that warmer air will be re-circulated throughout the house to keep you warmer and help keep your energy bills down at the same time.