Signs You Should Replace Your Springfield Heat Pump

April 2nd, 2012

The decision to replace major equipment can be a difficult one. How do you know when to call it quits on a part of your Springfield heating and cooling system that is as important as the heat pump?

Here are some signs that you should replace your heat pump:

  • Springfield Heat Pump RepairIf your Springfield heat pump is making unusual noises, its probably a sign that something is wrong. You should definitely call a professional to take a look at your heat pump as soon as possible, and, depending on what is causing the the noise, you might need to replace your heat pump.
  • Just like in your car, some repairing some parts of your heat pump are so expensive that it might be cost effective to just replace the whole unit. If your compressor, outdoor coil, or reversing valve break, you should seriously consider a new heat pump as an option. A new heat pump will work more efficiently and need fewer repairs, so it really is a good investment if your current heat pump is constantly breaking down.
  • A malfunctioning heat pump can cause problems with the humidity in your home. This is not a definitive indicator, but if you notice the humidity level rising in your home, you may need a heat pump replacement.
  • If your heat pump starts using much more energy than it used to it can be a sign of a major problem. If your energy bills suddenly rise, check your heat pump to see if you need to have it repaired or replaced.
  • If you notice a cooling imbalance, such as rooms being too warm while others are too cool, your heat pump may be close to breaking.
  • Finally, if your heat pump is ten or more years old, replacing it is a good idea, even if it seems to be working fine. A new model will be much more efficient and chances are that the old one is headed for a major breakdown soon.

Keep in mind that these are not always definitive signs that your heat pump is done for good. Also, some of these may occur in combination. For example, you may have an old heat pump that is making a lot of noise and causing humidity problems.

Consult with a professional for full diagnostics before making the decision to replace any major household equipment. If you have any questions about installing a new heat pump, give Cool It Heating & Air Conditioning a call!

Photo by One Tree Hill Studios: http://www.flickr.com/photos/endora57/54149221/

Tags: , , , , ,
Posted in Heat Pumps | Comments Off

Springfield Heat Pump Question: What is the Emergency Setting on My Heat Pump?

March 26th, 2012

While installing or inspecting your Springfield heat pump, you may have noticed that little switch or button labeled something like “Emergency Mode.” And then, you probably scratched your head and thought, “what is that for?”

Hopefully, the emergency setting is not something you will ever have to use. But, it is there for a reason, so it’s possible you may have to resort to it at some point. In that case, it makes sense to know what it is first.

Springfield Heating Repair- Air Source Heat PumpYour emergency setting is what turns on when your Springfield heat pump starts malfunctioning. The compressor will turn off so the heat pump is no longer transferring heat from the outside into your home as it normally would. Instead, the internal heating element comes on to provide your home with minimal heat until the device is working again. However, since your heat pump is now using electric resistance heating to heat your home, it is using a lot more energy. This can be very expensive, so it is best to have your heat pump fixed as quickly as possible.

That’s what the emergency setting is, but when would you use it?

It’s not a trick question. As the name implies, you only want to use this setting in an emergency. For example, if the heat pump has frozen and isn’t operating, the best course of action is to switch on the emergency mode and call a Springfield heating and air conditioning professsional to repair it.

You would also want to use the emergency mode when recovering from a power outage. Any time a heat pump is without power for more than thirty minutes the refrigerant can cool and get too thick to properly flow through the coils. Turning the pump back on in this situation can damage it, so instead you would use the emergency mode for a while to warm the refrigerant back up, then return to operating the heat pump normally.

The emergency setting is not to be used in place of a supplemental heating system. If there is an uncharacteristic cold snap, and your heat pump can’t keep up, then it makes sense to use the emergency setting to keep the house warm. However, if you live in a colder northern climate, where temperatures routinely drop below 30 degrees in the winter, you should have a supplemental heating system in addition to the heat pump. Using the emergency heat setting regularly is not a good idea.

For more information about maintaining your home’s heat pump, give Cool It Heating & Air Conditioning a call today!

Photo by k_lis: http://www.flickr.com/photos/krzlis/6589545719/

Tags: , , , , ,
Posted in Heat Pumps | Comments Off

Media Heating Installation Tip: Heating Upgrades and Home Energy Audit

March 21st, 2012

Considering an upgrade to your Media heating system? It’s usually a sound investment that generates savings both in heating costs and repair bills, plus it keeps your family happy and comfortable.

Before you take the plunge on new equipment, though, you may want to get a home energy audit. What you find may help you choose the right system.

A home energy audit is essentially an inspection by a professional of the materials used to insulate your home. This includes not just the insulation in the walls, but also the walls themselves, along with windows, doors and so on. The idea is to figure out how much heat is escaping your home to the outside, so an audit may also include looking at ducts, vents or anywhere else where air could flow through.

So what does an energy audit have to do with your Media heating upgrade?

Think about it like this. There are two ways to make your home warmer: increase heat gain (e.g., get a more efficient heating system) or decrease heat loss. If you are able to do the latter, you may find that the former is unnecessary.

For example, you may get an energy audit and discover that by installing new windows and resealing your doors, you can increase heating efficiency by 10%. This could have big implications for your decision to get a new heating system, as you may decide that you can save money by getting a smaller capacity furnace. Getting the right size furnace is very important; one that is too small will not be able to heat your home to the desired temperature and one that is too large will short-cycle, which leads to uneven heating and wears down your system quickly.

A home energy audit is the first step to getting a new heating system, and one that is sure to save you money.

While we do not provide home energy audits, please give Cool It Heating and Air Conditioning if you have any questions about your new system installation!

Tags: , , , , ,
Posted in Heating | Comments Off

Springfield Geothermal Contractor Guide: Installation Steps

March 14th, 2012

Are you interested in geothermal heating for your Springfield home? Are you considering using the natural heating and cooling energy of the Earth as a way to keep your home at a comfortable temperature?

If you are, you probably have a lot of questions, not the least of which have to do with the installation process. You may assume that it is complicated, but in most cases it is quite simple. Here is a simple summary of the steps involved in installing a geothermal system:

  1. The very first step, before any kind of installation can even be planned, is to evaluate the ground on which your home sits to be sure it can support a geothermal system. The area must be evaluated for soil and rock composition, availability of ground and surface water and availability of land.
  2. Once you have determined that your yard can handle a geothermal system, it is time to choose the type of system you need. This depends a lot on the evaluation from step 1, as well as some other factors. For one example, if you have very little land available, you may need to opt for a vertical loop configuration. For another, if you are fortunate enough to have a small body of water on your property, you can take advantage of a pond loop installation.
  3. Your contractor will dig and/or drill trenches for placement of the geothermal pipes. Try not to be nervous. They will disrupt your yard as little as possible.
  4. With the trenches prepared, pipes can be placed in accordance with the configuration you chose.
  5. Your contractor will fill the trenches back in to cover the pipes loosely. You may want to work with a landscaper to fully “re-assemble” your yard where the pipes were installed.
  6. Finally, the installation team will hook up the geothermal system to your home, make any necessary final adjustments, and you are good to go!

If you’re interested in geothermal heating for your Springfield home, consider contacting Cool It Heating & Air Conditioning today to discuss the installation process for your home.

Tags: , , , , ,
Posted in Geothermal | Comments Off

West Chester HVAC Guide: Different Types of Furnace Filters

March 7th, 2012

A good filter for your West Chester home’s furnace is a must. Because that device heats and blows air throughout your home, you want to be sure that it doesn’t recycle contaminants and bacteria that could easily be captured at the air handler. That’s why it’s vital to choose the right furnace filter on the first try. Here are some furnace filters to consider and their various benefits to your home and family:

  • Electrostatic – Most electrostatic filters are permanent and must be washed on a regular basis. They are electronically charged to capture particles as they pass through, much like a magnet. These filters are effective because they are both physical and electronic. However, keep in mind that they are only as efficient as the cleaning they receive.
  • HEPA – HEPA is the highest rating available for a filtration system, removing up to 99.9% of all particles as small as 0.3 microns. However, they are also inefficient when used in furnaces as they severely reduce air flow. They are not often recommended for this reason.
  • Pleated – Pleated filters come in both reusable and permanent forms and can be either purely mechanical or electrostatic. There is a very wide range of efficiency ratings for pleated filters so make sure you analyze your home’s specific needs before selecting any one pleated filter.
  • Activated Carbon – Activated carbon is unique from the other three filter types because it effectively removes fumes, odors and chemicals from indoor air along with other larger particles. It is recommended that if you choose an activated carbon filter, you supplement it with a pleated or electrostatic filter (or choose a combination filter) to remove all unwanted components from your home.

There are a lot of options when it comes to furnace filters. To make sure you get only the best air quality, talk to Cool It Heating & Air Conditioning who can help you determine which pollutants are the biggest problem in your home.

Tags: , , , , ,
Posted in Heating | Comments Off

Common Heat Pump Performance Problems: A Troubleshooting Guide from Broomall

February 29th, 2012

The heat pump in your Broomall home needs to work year round to provide heat and air conditioning. This is why you want to make sure it’s performing as efficiently as possible to save on energy costs and prevent break downs. You should schedule an annual maintenance check-up and inspection with a certified HVAC technician to test the efficiency levels.

However, there are a few common causes of performance issues to be aware of so that you can be sure your heat pump performs at optimal levels. Call Cool It Heating & Air Conditioning if you have questions about heat pump performance issues, or to make an appointment for an annual inspection and professional cleaning.

Airflow Issues

There should always be a certain amount of airflow (measured in cubic feet per minute) in your heat pump to maintain proper efficiency levels. If the airflow is less than 350 cfm per ton, it could increase your energy costs. You should make sure your HVAC contractor checks the airflow whenever your heat pump is inspected. Always keep the coils clean. Sometimes the ducts are not the right size, or the fan speed needs to be increased, but often cleaning the coils will help airflow, which is why it is important to clean and maintain the components of your heat pump. A certified technician will know what methods are best, so if you suspect an airflow problem with your heat pump, call a professional heating technician.

Air Leaks in the Duct System

Inefficient or poorly-designed duct systems may not distribute air properly throughout your home because of potential air leaks. There should always be a balance between the intake and return air in a forced air system, which helps maintain a neutral pressure within the house and increase efficiency. Some contractors argue over how tightly a house should be sealed for this reason, but if your heat pump is losing heat through leaks in the air ducts, this will greatly affect its efficiency.

Improper Refrigerant

Refrigerant leaks are another common cause of low performance levels in heat pumps. Most heat pumps already have refrigerant when they leave the factory and shouldn’t have any issues. Heat pumps that are charged with refrigerant when they are installed can sometimes have the wrong amount of refrigerant. Either too much or too little refrigerant will lower the heat pump’s efficiency and performance levels. Always check the recommended refrigerant amount or ask an HVAC technician before you add refrigerant yourself.

If the heat pump in your Broomall home isn’t working properly, it is also affecting your heating bills. Call Cool It Heating & Air Conditioning today to set up an appointment.

 

Tags: , , , , ,
Posted in Heat Pumps | Comments Off

Newtown Square Heating Repair Question: Can Your Heating System Warn You of a CO Leak?

February 24th, 2012

As everyone in Newtown Square knows, carbon monoxide is a serious health risk. It is an odorless gas that is produced as a natural byproduct of combustion. So, any time something burns, carbon monoxide (CO) is released into the air.

As long as the area is properly ventilated, the carbon monoxide cannot build up in the air to a dangerous level of concentration. For example, if you are around a campfire or charcoal that is burning outside, you are generally safe.

In the home, the danger arises when combustion is not properly ventilated and this toxic gas is allowed to seep into our living spaces. If you use any gas, fuel or wood burning appliances in your home, you are at risk for exposure to carbon monoxide. To help mitigate that risk, it is important to know some warning signs. Your heating system gives off some warnings that can tip you off to danger, so be on the lookout for these three signals:

  1. Carbon monoxide detector goes off. Some heating systems these days have built-in carbon monoxide detectors, which can provide an extra measure of safety. Whether you have one of these systems or not, your home should still be equipped with a CO detector. If it begins sounding the alarm, get everyone out of the house immediately.
  1. A fume vent is leaking. Fuel-burning furnaces have vents to move combustion gases out of the house safely. If you notice this vent is leaking on your heating system, CO may be seeping into your house. Shut down the furnace, open windows for ventilation and have the fume vent repaired immediately.
  1. Smoke backing up from the fireplace. If you have a fireplace and you notice smoke in the room while using it, stop using it immediately. Your chimney may be blocked or leaking, preventing the smoke from rising and venting properly, which means CO can e getting into your house. Do not use the fireplace again until you have had the chimney inspected.

Please take care and note this is just a simple guide. There are other risks and warnings of carbon monoxide. If you have any suspicion that there is CO in your home, immediately call Cool It Heating & Air Conditioning to look into the situation.

Tags: , , , ,
Posted in Heating | Comments Off

Gradyville Furnace Repair Question: What Causes Cracks in a Heat Exchanger?

February 22nd, 2012

Furnaces are designed so that the heat – and the combustion byproduct produced inside – doesn’t interact directly with the outside air. This design is to ensure you have a safe furnace in your Gradyville home that won’t inadvertently affect your family’s health.

The metal piece that separates the furnace heat from the outside air stream is called the heat exchanger. The heat exchanger performs a very important function, and if it is broken or cracked, it can’t work properly.

A cracked heat exchanger is very common problem with heating systems, as well as one that should be repaired as soon as possible. But what causes a heat exchanger to crack? Here are some of the most common reasons:

  • A long period of normal use. A furnace heat exchanger naturally expands and contracts with the heat of the furnace, over and over again as the furnace is turned off and on to heat the home. Over several years, this stress can crack the metal.
  • Poor air flow, often caused by dirty or obstructed vents, can result in poor air flow through the furnace. This overworks the furnace, which can crack the heat exchanger prematurely.
  • Poor, incomplete or improper combustion can also cause a heat exchanger to crack. When the combustion process is less efficient – which can also be a result of poor air flow — your furnace’s burners have to run hotter and longer to heat your home, which means extra stress on the heat exchanger.

Essentially, if a furnace is running at less than optimal efficiency for an extended period of time, the heat exchanger is put under additional stress beyond the usual and can crack prematurely. Therefore, the best way to prevent a cracked heat exchanger is proper maintenance, particularly keeping all vents clean and unobstructed and getting an annual maintenance inspection.

If your heat exchanger does crack, do not hesitate to call Cool It Heating & Air Conditioning and get it repaired. The crack can allow potentially dangerous combustion gases to seep into your home, which can have a negative impact on your family’s health.

Tags: , , , , , ,
Posted in Heating | Comments Off

Happy President’s Day from Your Greater Delaware County Area HVAC Contractor!

February 20th, 2012

Everyone at Cool It Heating and Air Conditioning wishes you a very happy President’s Day! We hope you all get a chance to take advantage of some of the great sales! It is also a great time to think about how you can make your community a better place. Lend a neighbor a helping hand or volunteer your time; everyone doing a little good can make a big difference!  Being more green is also a good way to help you community, and upgrading your HVAC system can be a big part of that. If you have an older system that is using a lot of fuel, a new system will not only save you money but also help you make your home more environmentally friendly, which is good for everyone.

One of the traditions of celebrating Presidents Day is food made with cherries, in honor of George Washington, so here is a great recipe for some Cherry-Blueberry Pie:

“A fruity and fun surprise awaits you inside this double crusted cherry and blueberry pie.”

INGREDIENTS:

1 (15 ounce) package refrigerated pie

crusts

1/2 cup white sugar

2 tablespoons cornstarch

1/4 teaspoon ground cinnamon

1 (21 ounce) can cherry pie filling

1 1/2 cups frozen blueberries

1 egg white

1 teaspoon water

2 teaspoons sugar

DIRECTIONS:

  1. Preheat the oven to 425 degrees F (220 degrees C).
  2. Press one of the pie crusts into a 9 inch pie plate. In a large bowl, stir together 1/2 cup of sugar, cornstarch and cinnamon. Stir in the cherry pie filling and blueberries. Spoon into the pie crust. Top with the second crust, and press the edges to seal. Flute edges, or press with the tines of a fork. In a cup, whisk together the egg white and water with a fork. Brush over the top of the pie, then sprinkle with 2 teaspoons of sugar.
  3. Bake for 45 to 55 minutes in the preheated oven, or until crust is golden brown. Cover the edges of the crust with aluminum foil if they appear to be getting too dark. Cool for at least 2 hours to allow the filling to set before serving.

This recipe is from allrecipes.com, visit their site for more details!

Tags:
Posted in Holiday | Comments Off

Villanova Heating Repair Tip: Reasons Your Furnace Is Producing No Heat

February 17th, 2012

The last occasion on which you want to worry about your furnace not producing any heat is the dead of winter, when the outside is chilly you just want to seek refuge in your own toasty Villanova home…only to discover that it’s not much warmer than the outdoors.

This may seem like a total emergency, and the combination of chill and frustration may cause panic to set in. Don’t start fretting too much just yet, though. There are some potentially simple causes and solutions for this problem, such as:

  • The thermostat may be set too low or on the wrong setting. Yes, it seems obvious, but sometimes the solution is staring you right in the face. Check that your thermostat is set high enough to call for heat and that it is on HEAT mode.
  • A circuit breaker may be tripped or a fuse may be blown. It could be the one dedicated to the thermostat, glow coil igniter or furnace itself. Check the breaker or fuse box in your home and either flip the breaker or replace the fuse. If it continues to trip or blow, get it looked at professionally—there may be a bigger problem going on.
  • The thermostat may not be working, so it is either improperly detecting the temperature or improperly reporting it to the furnace, so the heat does not kick on. Either way, it probably needs to be replaced.
  • The furnace is not igniting properly. This could mean the pilot light is out on furnaces without electric ignition, the gas valve is closed and can’t ignite or some other ignition malfunction. Check the pilot and gas valves to make sure they are on and working.

If you have checked all these things and the thermostat still is not working, or if you don’t feel comfortable looking into these causes on your own, you are best served by calling a professional repairman like Cool It Heating and Air Conditioning to diagnose and fix the furnace.

Often, these big failures are just the symptom of a smaller problem, so in all likelihood you won’t have to replace the furnace or do any major repairs, especially if it has been well-maintained throughout its life.

Tags: , , , , ,
Posted in Heating | Comments Off

« Older Entries
Newer Entries »