Archive for August, 2011

« Older Entries

Choosing an Environmentally Friendly Refrigerant for Your Air Conditioner: A Guide From Wallingford

Wednesday, August 31st, 2011

For years in Wallingford, we have heard about how bad air conditioners are for the environment. Specifically, the liquid used in them to remove heat from air in your home tended to eat holes in the Ozone layer. Today however, air conditioners (along with every other appliance or device that uses refrigerant) have been upgraded to work with newer, better chemicals.

R-22 Refrigerant

While R-22 refrigerant is still used in devices sold today, it is being gradually phased out. According to the Montreal Protocol, R-22 refrigerant will no longer be allowed in new devices as of January 1, 2020 in the United States (though it can be used to service existing devices via recycled or reused refrigerant). While the most environmentally damaging refrigerants such as HCFC-141b have been removed from the market, R-22 is still considered harmful to the environment if allowed to enter the atmosphere.

R-410A Refrigerant

So, if R-22 will soon not be permitted (and is not an environmentally friendly option), what is? Currently, the most common refrigerant used in new residential air conditioners is R-410A. After the Clean Air Act was passed, the EPA reviewed a number of refrigerants to determine which were the least damaging to the environment (and human health) and which could be used as alternatives to R-22. At the top of the list is R-410A, a blend of different HFCs that don’t deplete the ozone. Sometimes called Puron, Forane, or Genetron AZ-20, R-410A is a good choice if you’re having a new system installed.

Other Alternatives

Of course, because R-410A is a hydrofluorocarbon, it does contribute to global warming and therefore is a risk to the environment, albeit in a much smaller capacity than older refrigerants. Recently, the EPA approved the use of HFO-1234yf – a chemical that pollutes 99.7% less than the current refrigerant used in car air conditioners. Whether it will be used in homes and commercial spaces remains to be seen, but the technology is advancing rapidly, allowing us to stay cool without sacrificing our planet’s health and future to do so.

Another alternative is to invest in an evaporative cooling system rather than a traditional air conditioner. These systems use no HFCs at all and therefore have zero impact on the ozone layer or global warming (other than the electricity they consume). They also use 80% less energy than traditional air conditioners. If you live in a dry, low humidity climate they are a great option. If you have more questions about environmentally friendly HVAC equipment, contact your local HVAC professional.

Tags: , , , ,
Posted in Services | Comments Off

What Can You Do Yourself if Your Central AC Unit Does Not Work? When Should You Call a Malvern Professional?

Monday, August 29th, 2011

If your air conditioning system suddenly stops working or is not keeping your Malvern house as cool as you think it should, the chances are good that you will have to call in a professional to make the necessary repairs and get you back on track. However, there are a few things you can do on your own before you make that call to ensure that this really is something you cannot take care of on your own.

While it may seem obvious, the first thing you should check is the thermostat to make sure that it is set to a temperature that will trigger the air conditioning to come on. If your thermostat for some reason is set too high, then the air conditioner will not receive the signal to start cooling the house. This is an easy fix, of course, and you will be back up and running in no time.

If the thermostat is indeed set where it should be, the next thing to check is the air filter. Most people with central air conditioning know that they should change the filter once every month or so, but this seldom actually happens.

If it has been a while since your air filter was changed, there is a good chance that it is clogged and therefore blocking air from circulating from the air conditioner through the rest of the house. This is an easy enough fix, as all you need to do is replace the current air filter and your system should be able to pick up right where it left of. However, if the blocked air filter has also caused ice to form behind it, you may have to wait for a couple of hours until the ice has a chance to thaw.

Next, you will want to check and make sure that the air conditioning system is actually getting power. Look to see if any of the breakers are tripped or if there may have been a current interruption for any other reason that is within your power to fix. If this is the case, though, it is a good idea to turn the air conditioning system off before you attempt to restore the power.

If none of these measures are able to get your air conditioning system up and running again, you should not hesitate to call a professional. Many air conditioning repairs are quite basic, but they still need to be performed by a licensed professional.

Tags: , , , ,
Posted in Services | Comments Off

Open vs. Closed Loop Systems in Geothermal: A Guide From Concordville

Friday, August 26th, 2011

Even people who are somewhat familiar with geothermal heating systems may not be aware that there are actually two types – open and closed loop systems. The difference, of course, is that the closed loop systems make use of a completely sealed loop of pipe filled with water, antifreeze or some combination of these that cycles through the pipe absorbing heat and transferring it to your Concordville home.

Open loop systems, on the other hand, are linked to a well casting and draw water from there to circulate throughout the system as a heat source. Particularly if you already have an appropriate well casting in place, you can often save a lot on your installation costs by putting in an open loop system rather than a closed loop.

If you do not already have a well, however, the installation of an open loop system might still be cheaper but not by as much. Also, the costs of operation after the initial installation are pretty comparable, so the relative costs associated with operating one type of system or the other should not weigh to heavily on your decision.

In fact, the best way to decide which type of geothermal heating system is right for you is to talk to an experienced contractor about your particular situation. They will be able to tell you exactly what the installation of each type of system will entail in your specific case and make informed recommendations about what type of system will work best for you.

No matter what type of geothermal heating system you do go with, though, you will be getting an excellent and inexpensive home comfort solution that will keep your indoor temperature at the right level all year round. That is because geothermal heat pumps, just like air source heat pumps, can be reversed during the warmer summer months to actually remove heat from your home. That way, you can stay cool in the summer and warm in the winter without having to pay for heating or air conditioning. If you need more information about how geothermal heating and cooling works, contact your local professional.

Tags: , , ,
Posted in Services | Comments Off

How Do I Reduce Dust in My Home? A Question From Narberth

Wednesday, August 24th, 2011

Dust is everywhere in Narberth. There is no way to stop it from occurring, so instead we turn to cleaning and filtration to keep the amount of dust circulating through the air to a minimum. Luckily, there are quite a few things you can do, even without installing new equipment, to reduce your dust levels.

Duct Cleaning

First on the list is regular duct cleaning. You dust your furniture and your floors, so why not clean out your ductwork? Properly cleaned ductwork is very important because of just how much stuff can build up in there over time. Imagine regular air flow in an enclosed space that never gets cleaned. How much dust and debris do you think could build up over the course of a year? Hint: it’s enough to keep a steady flow of dust in your indoor air.

Professional duct cleaning is important and should be done once every year or two depending on how often you use your home comfort system. However, you should also clean in and around the vents and ducts in your home where you can reach. This can be done weekly and will help immensely to reduce dust.

Filtration

Most air filters equipped with high quality HEPA filters work extremely well to remove dust from the air. Because HEPA filters can capture particles as small as 0.3 microns, they won’t just remove dust, but pollen, pet dander and even mold. Mold especially is a problem that occurs in far greater frequency in homes without filtration.

Simple air filtration is an affordable solution to a lot of different contaminants, so it’s a good fit for any home. However, there are more powerful systems as well that will reduce both dust and pathogens like bacteria – these purifiers use ionization to draw particles from the air electronically.

Humidity

Humidity imbalance can cause dust problems as well. Low humidity leads to more dead skin and dust in the house, while high humidity causes the development of dust mites. Properly regulating your humidity to slightly less than 50% will create a perfect environment in which less dust is created and circulated in your home.

The best way to reduce dust is to take a three pronged approach to indoor air quality. Cleanliness is always first on the list, but after that don’t neglect the value of filtration and proper humidity control. When used properly, these three things will ensure dust never bothers you again.

Tags: , , , , ,
Posted in Services | Comments Off

A Simple Household Cleaning Tip From Folsom: How to Maintain Good Indoor Air Quality

Monday, August 22nd, 2011

There are a lot of reasons to clean. Guests, children, pets, simple peace of mind – without the right amount of cleaning, a messy Folsom house can quickly get out of control. But, don’t forget the health benefits of removing excess dust and sediment from your home with regular cleaning. To ensure your indoor air quality doesn’t take an unnecessary hit, here are a few basic cleaning tips you can implement right away.

  • Regular Vacuuming  – Most people vacuum occasionally when it’s obvious that carpets are getting a little messy. Consider increasing the frequency of your vacuuming to at least 3-4 times per week, possibly more, especially if you have pets. Regular vacuuming removes a lot of the airborne particles that can get into your lungs and cause allergies or asthma flare ups.
  • Remove Junk from Floor Spaces – Toys, garbage, clothes, and other random junk sitting on the floor can create air quality problems, especially if they are near or around vents.
  • Bathe and Brush Pets – Pet dander is a top contributor to indoor air quality problems. Bathe and brush your pets once a week to reduce hair loss and get rid of all that excess dander that builds up over time. Consider it an investment in the cleanliness of your home.
  • Shoes Outside – Shoes bring in pollen and other outdoor pollutants. Take them off outside and you will reduce the number of contaminants that make it inside.
  • Remove Moisture from Bathrooms – Bathroom moisture results in mold growth and the development of other allergens. Wipe down the walls of your shower and mop the floor daily to remove excess moisture after showers.
  • Food Waste – Throw away food waste immediately. Food in the sink or garbage can attracts bacteria and bugs and can result in mold growth very quickly. Consider a compost bucket or pile outside where food waste can be disposed or purchase a garbage disposal to get rid of it immediately after eating.

There are dozens more little things you can do that will reduce the amount of allergens and pollutants that build up in and around your home. Consider creating a simple calendar schedule you can follow from day to day to keep your indoor environment clean and healthy. If you have more questions about how maintain good indoor air quality, contact your local professional.

Tags: , , , ,
Posted in Services | Comments Off

What to Do About Cool Spots: A Tip From Boothwyn

Friday, August 19th, 2011

Sitting in your Boothwyn home on your couch watching TV should be an enjoyable experience, especially after a long day at the office. But, if your air conditioner deposits an abnormally high volume of cold air directly onto your couch, making you shiver despite the 90 degree heat outside, you may have a cool spot.

Cool spots are an unfortunate side effect of modern air conditioning technology. They occur when HVAC systems are improperly sized or ductwork is improperly installed. Other factors like insulation, vent configuration or window placement can also contribute to the presence of a cool spot (and possibly some hot spots). So, what can you do about it? There are a few options, starting with a quick inspection of the space.

Checking for Common Problems

Your inspector will check a number of things. Most importantly, they’ll measure the size of your HVAC system and compare it to the dimensions and particulars of your house. Usually, in the case of cool spots, the problem is directly related to an oversized system. When it turns on, even for a few minutes, it produces more cold air than is necessary, flooding your home with cooling. The thermostat recognizes this and the system shuts off soon after turning on. As a result, you’ll feel fluctuation between cold and warm as the system fails to properly condition the space.

Modern systems are sized for your house at 100% capacity. So, when the system turns on, it should stay on for a substantial period of time, keeping your home cool. Turning off and on frequently is bad for the system and wastes energy (plus it produces those pesky cool spots). Keep in mind that hot spots can also occur if the system isn’t powerful enough.

Your inspector will also look for vent placement and duct configuration. Improper placement of vents can lead to pooling of cool air that creates cool spots. By checking for potential problems in the layout of your HVAC system, an inspector can determine if new vents or ducts are needed to solve the problem.

Fixing the Cool Spots

For now, you may just want to move to another part of the house. Cool spots rarely affect the entire space – they tend to cluster around vents and outlets and can usually be fixed by resizing or adjusting your system. However, only your contractor can tell you for sure what the best solution will be for your air conditioning issues so make sure to schedule an inspection.

Tags: , , ,
Posted in Services | Comments Off

Federal Energy Efficiency Rebates Explained: A Guide From Broomall

Wednesday, August 17th, 2011

You’ve probably seen the advertisements and heard the sales pitches all over Broomall. Upgrade your furnace, air conditioner, water heater, or insulation and receive a federal rebate on your taxes for a percentage of the installation cost. The government is seriously invested in improving the energy efficiency of the country, cutting electric bills and helping people stay comfortable. Here’s a quick look at some of those rebates and how you can tap into them.

Energy Efficiency Credits

There is a standard tax credit of 10% of the cost up to $500 or a specific amount between $50 and $300 for any upgrade made to your existing home for heating, ventilation, air conditioning, insulation, roofs, or water heaters. These upgrades must be made on an existing home in which you currently live – rentals and new construction homes are not eligible.

Green Energy Credits

Even better credits are available if you plan on installing a geothermal heat pump, wind turbine or solar system – either PV panels or solar heating. The tax credit here is 30% of the cost with no upper limit. This applies to any existing or new homes and can be applied to both primary and secondary residences.

Are the Tax Credits Worth It?

The big question is whether these credits are worth the investment in a brand new system? For the most part, it depends on your particular situation. If you have a 30 year old furnace and are planning on an upgrade anyways, why not take advantage of a nice rebate and get a more energy efficient system to go with it? However, if you just replaced your furnace three years ago and it works very well with a high energy efficiency rating, it might not be worth the investment.

Learn More

The Energy Star program run by the EPA contains detailed breakdowns of the 2011 tax credits, including what systems are eligible and how to go about claiming them on next year’s taxes. Learn more by visiting their official page.

Tags: , , , , , ,
Posted in Services | Comments Off

How Do EER and SEER Work? A Question From Brookhaven

Monday, August 15th, 2011

If you’ve looked for a new air conditioner in Brookhaven recently, you probably noticed each unit comes with an EER or SEER rating. The former is for room air conditioners and the latter for central air conditioning units. In both cases, the number is a measure of how efficiently the system uses electricity. Effectively, if you buy a system with a high rating, you spend less on electricity. Of course, there are tradeoffs. The higher rated machines tend to cost much more, so as a homeowner, you’ll have to evaluate how much you can spend now and how long it will take to save money from that investment.

How EER and SEER Are Measured

These numbers are required by the government to tell you, the consumer, how many BTUs per hour the device can use for every watt of electricity drawn. The more BTUs a system can use, the better for your bill.

Let’s say you want to buy a 10,000 BTU system to cool your living room and dining room. A pretty standard number for a single room unit is 11, meaning the 10,000 BTU system would use about 900 watts per hour to run at full capacity. We figure this out by dividing the BTUs (10,000) by the watts (900).

There is a lot of math to do here, so many people simply look for a higher number within their price range. But, at what point is the upgrade really worth your extra money?

Choosing the Right Energy Efficiency Rating

The easiest way to describe this is to compare two similar devices with different EERs:

Air Conditioner 1 Air Conditioner 2
BTUs 12,000 12,000
EER 9 11
Watts 1333 1091
Price $300 $450

In this particular case, we can spend more for a device that is the same size but uses less electricity. The question then is whether that increased expenditure will pay off in the short term. Let’s assume each device would be operated for 10 hours per day for 30 days in a typical summer month. That’s 300 hours of operation. If the average cost per kWh in you are is $0.09, it will take 4 hours for the first air conditioner to consume 1 extra kilowatt of electricity equal to an additional $0.09. If your air conditioner runs for four months out of the year, we know that it will operate for a total of 1200 hours. That means:

[(1200 hrs x 242 watts) / (1000 watts/kw) ] x $0.09/kWh = $26

So, you save roughly $26 per year from that high efficiency unit. With a $150 price difference, you will break even after 6 years (though probably sooner if the price of electricity goes up).

Don’t forget, however, that central systems are a much more efficient option with SEERs of up to 16.5 and much larger BTU areas to cover. The savings there can add up very quickly. If you need more information to decide which air conditioner is right for you, talk to your air conditioning professional.

Tags: , , , , ,
Posted in Services | Comments Off

Mold…What if I Have Mold? A Question From Thornton

Friday, August 12th, 2011

No one wants to find mold. But, even if you’re not aware of it, mold is probably lurking somewhere in the damp, dark crevices of your Thornton home. And mold is particularly likely to grow in homes with improperly regulated humidity. Luckily, because we know that, there are quite a few things we can do to stop the growth of mold in its tracks and save your home from unsafe air quality and the damaging effects of those little spores.

The Dangers of Mold

As mold grows, it can do damage to your woodwork and other areas of your home. It also contributes to indoor air quality issues because mold spores are a significant indoor air contaminant. Many people are allergic to mold spores, so if you or someone else in your household has experienced allergy symptoms that you can’t explain, mold spores are a likely culprit.

If you find out there is mold in your home, don’t panic just yet. There are some things you can do to address the problem and get mold out of your house for good. Your main task will be getting rid of the mold that is already there. This isn’t necessarily easy because of the areas mold tends to grow in. But, even with the proper air quality treatment, your home and health is still at risk if you don’t target that existing mold fast.

Stopping Mold in Its Tracks

Just getting rid of existing mold won’t solve the problem, though. Mold keeps coming back as long as there is an environment to support it – and that means moisture. Mold requires water to grow, so the chances are that if you have a mold problem in your home, you also have a humidity problem. Getting your indoor humidity under control will make it much easier to remove and keep mold out of your home for good.

There are plenty of good humidification systems on the market today. They can be easily integrated into your home heating and cooling system and provide great, consistent humidity control. Make sure you get one that’s large enough for your home. An indoor air quality professional can help you make that determination. Once you have a good humidification system in place, you’ll notice a huge difference in your overall indoor air quality, and hopefully the problem won’t return anytime soon.

Tags: , , , ,
Posted in Services | Comments Off

Maintenance Really Does Save Money in Gradyville

Wednesday, August 10th, 2011

When it comes to your Gradyville home heating and cooling systems, you really cannot go wrong with proper annual maintenance. While it may seem like an unnecessary expense, especially if your systems are relatively new, you will save a lot in the long run if you pay that small fee once a year for each system.

During a maintenance visit, a technician can thoroughly clean out your heating or cooling system and check all parts to make sure they are not showing signs of excessive wear and tear. If they do find a problem or a part that needs to be replaced, they will be able to make the necessary repairs quickly and you will not have to worry about calling someone out later for an emergency visit.

Also, catching problems early like this means that repairs will likely involve fewer parts and cost much less than they would if you let the problem go and it became more widespread. The truth is that your heating or cooling system can continue to work when one or another of its parts is not working correctly, but that means that other parts of the system have to work overtime to create the same result.

Your heating or cooling system will also be much more energy efficient if it receives regular tune ups and attention from a professional. Even the best new systems lose a small percentage of their efficiency each year that they are in operation. While this is not much from year to year, the cumulative effect will soon cause your energy bills to climb higher than necessary.

Paying for regular maintenance, then, can actually save you money because it will mean you pay less each month to run your system. And it is never too late to start. Even if your heating or cooling system is not new, it will benefit from a thorough cleaning and tune up. You may be quite surprised how much your energy bills go down after this type of service has been performed.

Annual maintenance can also help you to get more for your money by extending the useful life of the heating or cooling system. Many systems that are properly maintained can last even beyond their expected life span, meaning that you will not have to replace it as soon as you would have otherwise. For all of these reasons, the minimal cost of an annual maintenance visit is well worth paying over the long term.

Tags: , , , , ,
Posted in Services | Comments Off

« Older Entries